View 893D_729768.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

893D
Vishay Sprague
Solid Tantalum Chip Capacitors TANTAMOUNT(R), Built-In-Fuse Miniature, Molded-Case
FEATURES
* Molded case available in three case codes. * Compatible with "High Volume" automatic pick and place equipment. * Electrically activated internal fuse. * Meets EIA 535BAAC and IEC Specification QC300801/ US0001.
PERFORMANCE/ELECTRICAL CHARACTERISTICS
Operating Temperature: - 55C to + 85C. (To + 125C with voltage derating.) Capacitance Range: 1.0F to 220F. Capacitance Tolerance: 20%, 10% standard. Compliant Terminations. Voltage Rating: 6.3 WVDC to 50 WVDC. 100% Surge Current Tested (D & E Case Codes).
ORDERING INFORMATION
893D TYPE 107 CAPACITANCE X9 CAPACITANCE TOLERANCE X0 = 20% X9 = 10% X5 = 5% (Special Order) 010 DC VOLTAGE RATING @ + 85C This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an "R" (6R3 = 6.3 volts). D CASE CODE 2 TERMINATION
_W
REEL SIZE AND PACKAGING T = Tape and Reel 7" [178mm] Reel* W = 13" [330mm] reel* *cathode nearest sprocket hole.
This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow.
See Ratings and Case Codes Table.
2 = Solderable coating. 4 = Gold Plated
Note: Preferred Tolerance and reel sizes are in bold print We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
L
H TH Min. TW
W
P
CASE CODE C D E
EIA SIZES 6032 7343 7343H
L 0.236 0.012 [6.0 0.30] 0.287 0.012 [7.3 0.30] 0.287 0.012 [7.3 0.30]
W 0.126 0.012 [3.2 0.30] 0.170 0.012 [4.3 0.30] 0.170 0.012 [4.3 0.30]
H 0.098 0.012 [2.5 0.30] 0.110 0.012 [2.8 0.30] 0.158 0.012 [4.0 0.30]
P 0.051 0.012 [1.3 0.30] .051 0.012 [1.3 0.30] 0.051 0.012 [1.3 0.30]
TW 0.087 0.004 [2.2 0.10] 0.095 0.004 [2.4 0.10] 0.095 0.004 [2.4 0.10]
TH (Min.) 0.039 [1.0] 0.039 [1.0] 0.039 [1.0]
www.vishay.com 38
For technical questions, contact tantalum@vishay.com
Document Number 40008 Revision 04-Feb-03
893D
Vishay Sprague
RATINGS AND CASE CODES
F
Std. 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 C C D D D D E C C C C D D D D E C C C C C D D D D E C C D D E E C C C C C C D D D E C D C D D D E E C D D D/E 6.3 V Ext. Std. 10 V Ext. 16 V Std. Ext. 20 V Std. Ext. Std. 25 V Ext. 35 V Std. Ext. 50 V Std. C C C C Ext.
MARKING
MARKING
Capacitance Voltage
Polarity Band
22 F 10 2 XX
Vishay Sprague Logo
Date Code
Marking: Capacitors shall be marked with an anode polarity band, capacitance (in microfarads) and the rated DC working voltage 85C. The capacitance voltage will be separated by the letter "F" indicating a fused capacitor. Units rated at 6.3 V shall be marked as 6 V.
STANDARD / EXTENDED RATINGS
CAPACITANCE (F) Max. DC LEAKAGE @ + 25C (A) Max. DF @ + 25C 120Hz (%) Max. ESR @ + 25C 100kHz (Ohms) Max. RIPPLE 100kHz Irms (Amps)
CASE CODE
PART NUMBER*
6.3 WVDC @ + 85C, Surge = 8 V...4WVDC @ + 125C, Surge = 5 V 22 33 47 47 68 68 100 150 220 C C C D C D D D E 893D226X_6R3C_ _ 893D336X_6R3C_ _ 893D476X_6R3C_ _ 893D476X_6R3D_ _ 893D686X_6R3C_ _ 893D686X_6R3D_ _ 893D107X_6R3D_ _ 893D157X_6R3D_ _ 893D227X_6R3E_ _ 1.1 1.6 2.3 2.3 3.3 3.3 4.8 9.0 13.2 6 6 6 6 6 6 8 8 8 1.8 1.4 1.3 0.9 0.8 0.7 0.7 0.6 0.5 0.25 0.28 0.29 0.41 0.37 0.46 0.46 0.50 0.57
* Preliminary values contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended ratings are in bold print.
Document Number 40008 Revision 04-Feb-03
For technical questions, contact tantalum@vishay.com
www.vishay.com 39
893D
Vishay Sprague
STANDARD / EXTENDED RATINGS
CAPACITANCE (F) 15 22 33 33 47 47 68 100 150 6.8 10 15 22 22 33 33 47 68 100 4.7 6.8 10 15 22 33 47 68 2.2 4.7 6.8 10 10 15 22 33 3.3 4.7 4.7 6.8 10 15 22 1.0 1.5 2.2 3.3 3.3 4.7 6.8 6.8 Max. DC LEAKAGE @ + 25C (A) Max. DF @ + 25C 120Hz (%) Max. ESR @ + 25C 100kHz (Ohms) 1.8 1.4 1.3 0.9 1.0 0.7 0.7 0.6 0.5 2.0 1.8 1.4 1.3 0.9 1.0 0.7 0.7 0.6 0.6 2.2 1.9 1.6 1.4 0.7 0.7 0.6 0.6 1.8 1.9 1.6 1.4 1.0 0.8 0.7 0.6 2.0 1.8 1.2 1.0 0.8 0.7 0.6 4.4 3.2 2.8 2.4 1.6 1.1 0.9 0.9 Max. RIPPLE 100kHz Irms (Amps) 0.25 0.28 0.29 0.41 0.33 0.46 0.46 0.50 0.57 0.23 0.25 0.28 0.29 0.41 0.33 0.46 0.46 0.50 0.52 0.22 0.24 0.26 0.28 0.46 0.46 0.52 0.52 0.21 0.24 0.26 0.28 0.39 0.43 0.46 0.52 0.23 0.25 0.35 0.38 0.43 0.49 0.52 1.60 0.90 0.20 0.21 0.31 0.37 0.41 0.43
CASE CODE C C C D C D D D E C C C C D C D D D E C C C C D D E E C C C C D D D E C C D D D E E C C C C D D D E
PART NUMBER*
10 WVDC @ + 85C, Surge = 13 V...7WVDC @ + 125C, Surge = 8 V 1.5 893D156X_010C_ _ 6 893D226X_010C_ _ 2.2 6 3.3 6 893D336X_010C_ _ 893D336X_010D_ _ 3.3 6 893D476X_010C_ _ 4.7 6 893D476X_010D_ _ 4.7 6 893D686X_010D_ _ 6.8 6 893D107X_010D_ _ 10 8 893D157X_010E_ _ 15.0 8 16 WVDC @ + 85C, Surge = 20 V...10WVDC @ + 125C, Surge = 12 V 893D685X_016C_ _ 1.1 6 893D106X_016C_ _ 1.6 6 893D156X_016C_ _ 2.4 6 893D226X_016C_ _ 2 3.5.8 6 893D226X_016D_ _ 3.5 6 893D336X_016C_ _ 5.3 6 893D336X_016D_ _ 5.3 6 893D476X_016D_ _ 7.5 6 893D686X_016D_ _ 10.9 6 893D107X_016E_ _ 16 8 20WVDC @ + 85C, Surge = 26 V...13WVDC @ + 125C, Surge = 16 V 893D475X_020C_ _ 0.9 6 893D685X_020C_ _ 1.4 6 893D106X_020C_ _ 2.0 6 893D156X_020C_ _ 3.0 6 893D226X_020D_ _ 4.4 6 893D336X_020D_ _ 6.6 6 893D476X_020E_ _ 9.4 6 893D686X_020E_ _ 13.6 6 25WVDC @ + 85C, Surge = 32 V...17WVDC @ + 125C, Surge = 20 V 0.9 6 893D225X_025C_ _ 1.2 6 893D475X_025C_ _ 1.7 6 893D685X_025C_ _ 6 2.5 893D106X_025C_ _ 2.5 6 893D106X_025D_ _ 3.8 6 893D156X_025D_ _ 5.5 6 893D226X_025D_ _ 8.3 6 893D336X_025E_ _ 35WVDC @ + 85C, Surge = 46 V...23WVDC @ + 125C, Surge = 28 V 893D335X_035C_ _ 4 1.2 893D475X_035C_ _ 6 1.6 893D475X_035D_ _ 1.6 6 893D685X_035D_ _ 6 2.4 893D106X_035D_ _ 6 3.5 893D156X_035E_ _ 6 5.3 893D226X_035E_ _ 6 7.7 50WVDC @ + 85C, Surge = 65 V...33WVDC @ + 125C, Surge = 40 V 0.5 893D105X_050C_ _ 4 0.8 893D155X_050C_ _ 6 1.1 893D225X_050C_ _ 6 1.7 893D335X_050C_ _ 6 1.7 893D335X_050D_ _ 6 2.4 893D475X_050D_ _ 6 3.4 893D685X_050D_ _ 6 3.4 893D685X_050E_ _ 6
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended range ratings are in bold print.
www.vishay.com 40
For technical questions, contact tantalum@vishay.com
Document Number 40008 Revision 04-Feb-03
893D
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1. Operating Temperature: Capacitors are designed to operate over the temperature range of - 55C to + 85C. 6. 1.1 Capacitors may be operated to + 125C with voltage derating to two-thirds the + 85C rating.
+ 85C Rating Working Voltage (V) 6.3 10 16 20 25 35 50 Surge Voltage (V) 8 13 20 26 32 46 65 + 125C Rating Working Voltage (V) 4 7 10 13 17 23 33 Surge Voltage (V) 5 8 12 16 20 28 40 - 55C - 10% + 85C + 10% + 125C + 12%
Dissipation Factor: The dissipation factor, determined from the expression 2fRC, shall not exceed values listed in the Standard Ratings Table. Measurements shall be made by the bridge method at, or referred to, a frequency of 120Hz and a temperature of + 25C. Equivalent Series Resistance: Measurements shall be made by the bridge method at, or referred to, a frequency of 100kHz and a temperature of + 25C. The equivalent series resistance shall not exceed the valued listed in the Standard Ratings Table.
6.1
7.
7.1
2.
DC Working Voltage: The DC working voltage is the maximum operating voltage for continuous duty at the rated temperature. Surge Voltage: The surge DC rating is the maximum voltage to which the capacitors may be subjected under any conditions, including transients and peak ripple at the highest line voltage. Surge Voltage Test: Capacitors shall withstand the surge voltage applied in series with a 33 ohm 5% resistor at the rate of one-half minute on, one-half minute off, at + 85C, for 1000 successive test cycles. Following the surge voltage test, the dissipation factor shall meet the initial requirements; the capacitance shall not have changed more than 5%; the leakage current at + 25C shall meet the initial requirements.
3.
Note that the leakage current varies with temperature and applied voltage. See graph below for the appropriate adjustment factor.
TYPICAL LEAKAGE CURRENT FACTOR RANGE
3.1
100
+ 125C + 85C 10 + 55C
3.2
Leakage Current Factor
+ 25C 1.0 0C
4.
Capacitance Tolerance: The capacitance of all capacitors shall be within the specified tolerance limits of the normal rating. Capacitance measurements shall be made by means of polarized capacitance bridge. The polarizing voltage shall be of such magnitude that there shall be no reversal of polarity due to the AC component. The maximum voltage applied to capacitors during measurement shall be 2 volts rms at 120Hz at +25C. If the AC voltage applied is less than one-half volt rms, no DC bias is required. Accuracy of the bridge shall be within 2%. Capacitance Change With Temperature: The capacitance change with temperature shall not exceed the following percentage of the capacitance measured at + 25C:
4.1
0.1
- 55C
0.01
0.001
5.
0
10
20
30
40
50
60
70
80
90
100
Percent of Rated Voltage
Document Number 40008 Revision 04-Feb-03
For technical questions, contact tantalum@vishay.com
www.vishay.com 41
893D
Vishay Sprague
PERFORMANCE CHARACTERISTICS (Continued)
8. Leakage Current: Capacitors shall be stabilized at the rated temperature for 30 minutes. Rated voltage shall be applied to capacitors for 5 minutes using a steady source of power (such as a regulated power supply) with 1000 ohm resistor connected in series with the capacitor under test to limit the charging current. Leakage current shall then be measured. At + 25C, the leakage current shall not exceed the value listed in the Standard Ratings Table. At + 85C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings Table. At + 125C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings Table. Life Test: Capacitors shall withstand rated DC voltage applied at + 85C for 2000 hours or derated DC voltage applied at + 125C for 1000 hours, with a current resistance no greater than 3 ohms. Following the life test, the dissipation factor shall meet the initial requirement; the capacitance change shall not exceed 10%; the leakage current shall not exceed 125% of the initial requirement. Vibration Tests: Capacitors shall be subjected to vibration tests in accordance with the following criteria. Capacitors shall be secured for test by means of a rigid mounting using suitable brackets. Low Frequency Vibration: Vibration shall consist of simple harmonic motion having an amplitude of 0.03" [0.76mm] and a maximum total excursion of 0.06" [1.52mm], in a direction perpendicular to the major axis of the capacitors. 11.2 0.06" [1.52mm] 10% maximum total excursion or 20 g peak whichever is less. 10.3.1 Vibration frequency shall be varied logarithmically from 50 Hz to 2000 Hz and return to 50 Hz during a cycle period of 20 minutes. 10.3.2 The vibration shall be applied for 4 hours in each of 2 directions, parallel and perpendicular to the major axis of the capacitors. 10.3.3 Rated DC voltage shall be applied during the vibration cycling. 10.3.4 An oscilloscope or other comparable means shall be used in determining electrical intermittency during the last cycle. The AC voltage applied shall not exceed 2 volts rms. 10.3.5 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 10.3.6 There shall be no mechanical damage to these capacitors as a result of these tests. 10.3.7 Following the high frequency vibration test, capacitors shall meet the original limits for capacitance dissipation factor and leakage current. 11. 11.1 10.1 10.2 Acceleration Test: Capacitors shall be rigidly mounted by means of suitable brackets. Capacitors shall be subjected to a constant acceleration of 100 g for a period of 10 seconds in each of 2 mutually perpendicular planes.
8.1 8.2 8.3 9.
9.1
10.
11.2.1 The direction of motion shall be parallel to and perpendicular to the longitudinal axis of the capacitors. 11.3 Rated DC voltage shall be applied during acceleration test.
10.2.1 Vibration frequency shall be varied uniformly between the approximate limits of 10 Hz to 55 Hz during a period of approximately one minute, continuously for 1.5 hours. 10.2.2 An oscilloscope or other comparable means shall be used in determining electrical intermittency during the final 30 minutes of the test. The AC voltage applied shall not exceed 2 volts rms. 10.2.3 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 10.2.4 Following the low frequency vibration test, capacitors shall meet the original requirements for capacitance, dissipation factor and leakage current. 10.3 High Frequency Vibration: Vibration shall consist of a simple harmonic motion having an amplitude of
11.3.1 An oscilloscope or other comparable means shall be used in determining electrical intermittency during test. The AC voltage applied shall not exceed 2 volts rms. 11.4 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 11.5 There shall be no mechancial damage to these capacitors as a result of these tests. 11.6 Following the acceleration test, capacitors shall meet the original limits for capacitance, dissipation factor and leakage current.
www.vishay.com 42
For technical questions, contact tantalum@vishay.com
Document Number 40008 Revision 04-Feb-03
893D
Vishay Sprague
12. 12.1 Shock Test: Capacitors shall be rigidly mounted by means of suitable brackets. The test load shall be distributed uniformly on the test platform to minimize the effects of unbalanced loads. 14.4 Following the thermal shock test, capacitors shall meet the original requirements for leakage current and dissipation factor. Capacitors change shall not exceed 5% of the original measuring value. Soldering Compatibility: Resistance to Solder Heat: Capacitors will withstand exposure to + 260C + 5C for 10 seconds.
15. 15.1
12.1.1 Test equipment shall be adjusted to produce a shock of 100 g peak with the duration of 6 mS and sawtooth waveform at a velocity change of 9.7 ft./sec. 12.2 Capacitors shall be subjected to 3 shocks applied in each of 3 directions corresponding to the 3 mutually perpendicular axes of the capacitors. Rated DC voltage shall be applied during test.
15.1.1 Following the resistance to soldering heat test, capacitance, dissipation factor and DC leakage current shall meet the initial requirement. 15.2 Solderability: Capacitors will meet the solderability requirements of ANSI/J-STD-002, Test B (MIL-STD202, method and Test S.) Terminal Strength: Per IEC-384-3, minimum of 5N shear force. Environmental: Mercury, CFC and ODS materials are not used in the manufacture of these capacitors. Flammability: Encapsulant materials meet UL94 V0 with an oxygen index of 32%. Fuse Activation: Shall not exceed the value listed in the Standard Ratings Table. Fuse Construction: Fuse material is constructed of two metalic elements in intimate contact with each other. Sufficiently high current cause these two metals to instantaneously deflagrate (exothermic fusing). Capacitor Failure Mode: The predominant failure mode for solid tantalum capacitors is increased leakage current resulting in a shorted circuit. Capacitor failure may result from excess forward or reverse DC voltage, surge current, ripple current, thermal shock or excessive temperature. The increase in leakage is caused by a breakdown of the Ta2O5 dielectric. For additional information on leakage failure of solid tantalum chip capacitors, refer to Vishay Sprague Technical Paper, "Leakage Failure Mode in Solid Tantalum Chip Capacitors." A shorted capacitor with an internal fuse will become an open circuit after dielectric breakdown. 22. Surge Current: All D and E case code 893D capacitors are surge current tested at + 25C and rated voltage. The total series circuit resistance is 0.5 ohms. Each charge cycle of 0.10 seconds is followed by a discharge cycle of 0.10 seconds. Three surge cycles are applied. Each capacitor is tested individually to maximize the peak charging current.
12.3
12.3.1 An oscilloscope or other comparable means shall be used in determining electrical intermittency during tests. The replacement voltage applied shall not exceed 2 volts rms. 12.4 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. There shall be no mechanical damage to these capacitors as a result of these tests. Following the shock test, capacitors shall meet the original limits for capacitance, dissipation factor and leakage current. Moisture Resistance: Capacitors shall be subjected to temperature cycling at 90% to 95% relative humidity, from + 25C to + 65C to + 25C (+ 10C, - 2C) over a period of 8 hours per cycle for 1000 hours. Following the moisture resistance test, the leakage current and dissipation factor shall meet the initial requirements and the change in capacitance shall not exceed 10%. Thermal Shock: Capacitors shall be conditioned prior to temperature cycling for 15 minutes at + 25C, at less than 50% relative humidity and a barometric pressure at 28 to 31ins. Capacitors shall be subjected to thermal shock in a cycle of exposure to ambient air at - 55C (+ 0C,- 5C) for 30 minutes, then + 25C (+ 10C, - 5C) for 5 minutes, then + 125C (+ 3C, - 0C) for 30 minutes, then + 25C (+ 10C, - 5C) for 5 minutes for 5 cycles. Capacitors shall show no evidence of harmful or extensive corrosion, obliteration of marking or other visible damage.
16 17. 18. 19. 20.
12.5 12.6
13. 13.1
21.
13.2
14. 14.1
14.2
14.3
Document Number 40008 Revision 04-Feb-03
For technical questions, contact tantalum@vishay.com
www.vishay.com 43
893D
Vishay Sprague
GUIDE TO APPLICATION
1. A-C Ripple Current: The maximum allowable ripple current shall be determined from the formula: Irms = where, P= Power Dissipation in Watts @ + 25C as given in the table in Paragraph Number 4 (Power Dissipation). P RESR 5. Power Dissipation: Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown. It is important that the equivalent Irms value be established when calculating permissible operating levels. (Power Dissipation calculated using + 25C temperature rise.)
Maximum Permissible Power Dissipation @ + 25C (Watts) in free air 0.110 0.150 0.165
RESR =The capacitor Equivalent Series Resistance at the specified frequency. 2. A-C Ripple Voltage: The maximum allowable ripple voltage shall be determined from the formula: Vrms = Z or, from the formula: Vrms = Irms x Z where, P= Power Dissipation in Watts @ + 25C as given in the table in Paragraph Number 5 (Power Dissipation). 7. 7.1 P RESR 6.
Case Code C D E
Printed Circuit Board Materials: The 893D is compatible with commonly used printed circuit board materials (alumina substrates, FR4, FR5, G10, PTFEfluorocarbon and porcelanized steel). Attachment: Solder Paste: The recommended thickness of the solder paste after applications is .007" .001" [1.78mm .025mm]. Care should be exercised in selecting the solder paste. The metal purity should be as high as practical. The flux (in the paste) must be active enough to remove the oxides formed on the metallization prior to the exposure to soldering heat. In practice this can be aided by extending the solder preheat time at temperatures below the liquidous state of the solder. Soldering: Capacitors can be attached by conventional soldering techniques - vapor phase, infrared reflow, wave soldering and hot plate methods. The Soldering Profile chart shows maximum recommended time/temperature conditions for soldering. Attachment with a soldering iron is not recommended due to the difficulty of controlling temperature and time at temperature. Cleaning (Flux Removal) After Soldering: The 893D is compatible with all commonly used solvents such as TES, TMS, Prelete, Chlorethane, Terpene and aqueous cleaning media. However, CFC/ODS products are not used in the production of these devices and are not recommended. Solvents containing methylene chloride or other epoxy solvents should be avoided since these will attack the epoxy encapsulation material. When using ultrasonic cleaning, the board may resonate if the output power is too high. This vibration can cause cracking or a decrease in the adherence of the termination. DO NOT EXCEED 9W/l @ 40kHz for 2 minutes.
Document Number 40008 Revision 04-Feb-03
RESR =The capacitor Equivalent Series Resistance at the specified frequency. Z= 2.1 The capacitor impedance at the specified frequency. 7.2
The sum of the peak AC voltage plus the DC voltage shall not exceed the DC voltage rating of the capacitor. The sum of the negative peak AC voltage plus the applied DC voltage shall not allow a voltage reversal exceeding 10% of the DC rating at + 25C, 5% of the DC rating at + 85C and 1% of the DC rating at + 125C. Reverse Voltage: These capacitors are capable of withstanding peak voltages in the reverse direction equal to 10% of the DC rating at + 25C, 5% of the DC rating at + 85C and 1% of the DC rating at + 125C. Temperature Derating: If these capacitors are to be operated at temperatures above + 25C, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown:
Temperature + 25C + 85C + 125C Derating Factor 1.0 0.9 0.4
2.2
3.
8.
4.
8.1
www.vishay.com 44
For technical questions, contact tantalum@vishay.com
893D
Vishay Sprague
SOLDERING PROFILE
Recommended Solder Profile -- Wave Solder
5 - 10 Sec. Recommended Solder Profile -- Reflow 300
Temperature Degrees Centigrade
Temperature Degrees Centigrade
300 250 200 150 150 100 50 50 0 0 0 50 100 150 200 250 130C Typical 100 245C Typical 250 200
300 250 200 150 100 50 0 0
Max. Recommended 260C
300 250 200
130C
150 100 50 0
50
100
150
200
250
Time (Seconds)
Time (Seconds)
9.
Recommended Mounting Pad Geometries: Proper mounting pad geometries are essential for successful solder connections. These dimensions are highly process sensitive and should be designed to minimize component rework due to unacceptable solder joints. The dimensional configurations shown are the recommended pad geometries for both wave and reflow soldering techniques. These dimensions are intended to be a starting point for circuit board designers and may be fine tuned if necessary based upon the peculiarities of the soldering process and/or circuit board design.
RECOMMENDED MOUNTING PAD GEOMETRIES in inches [millimeters]
Wave Solder Pads
D B C B E C E
Reflow Solder Pads
D
A
A
Pad Dimensions Case Code C D E A (Min.) 0.061 [1.54] 0.066 [1.68] 0.066 [1.68] B (Nom.) 0.106 [2.70] 0.106 [2.70] 0.106 [2.70] C (Nom.) 0.124 [3.15] 0.175 [4.45] 0.175 [4.45] D (Nom.) 0.337 [8.55] 0.388 [9.85] 0.388 [9.85] E (Nom.) 0.050 [1.28] 0.050 [1.28] 0.050 [1.28] Case Code C D E A (Min.) 0.110 [2.80] 0.118 [3.00] 0.118 [3.00]
Pad Dimensions B (Nom.) 0.106 [2.70] 0.106 [2.70] 0.106 [2.70] C (Nom.) 0.124 [3.15] 0.175 [4.45] 0.175 [4.45] D (Nom.) 0.337 [8.55] 0.388 [9.85] 0.388 [9.85] E (Nom.) 0.050 [1.28] 0.050 [1.28] 0.050 [1.28]
Document Number 40008 Revision 04-Feb-03
For technical questions, contact tantalum@vishay.com
www.vishay.com 45
893D
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
K Max. 0.024 [0.600] Max.
0.059 + 0.004 - 0.0 [1.5 + 0.10 - 0.0]
0.157 0.004 [4.0 0.10]
0.079 0.002 [2.0 0.050]
0.069 0.004 [1.75 0.10]
A0
F
W
B1 Max.
K0
B0
P Top Cover Tape Direction of Feed D1 Min.
TAPE SIZE 8mm 12mm
B1 (Max.) 0.165 [4.2] 0.323 [8.2]
D1 (Min.) 0.039 [1.0] 0.059 [1.5]
F 0.138 0.002 [3.5 0.05] 0.217 0.002 [5.5 0.05]
K (Max.) 0.094 [2.4] 0.177 [4.5]
P
W
A0B0K0
Notes: A0B0K0 are determined by component size. 0.157 0.004 0.315 0.012 The clearance between the component and the [8.0 0.30] cavity must be within 0.002" [0.05mm] minimum to [4.0 1.0] 0.315 0.004 0.472 0.012 .020" [0.50mm] maximum for 8mm tape and 0.002" [12.0 0.30] [0.05mm] minimum to 0.026" [0.65mm] maximum [8.0 1.0] for 12mm tape.
Standard orientation is with the cathode (-) nearest to the sprocket holes per EIA-481-1 and IEC 286-3.
Top Cover Tape Thickness
Tape and Reel Specifications: All case codes are available on plastic embossed tape per EIA-481-1. Tape reeling per IEC 286-3 is also available. Standard reel diameter is 13" [330mm]. 7" [178mm] reels are available. The most efficient packaging quantities are full reel increments on a given reel diameter. The quantities shown allow for the sealed empty pockets required to be in conformance with EIA-481-1. Reel size must be specified in the Vishay Sprague part number.
Carrier Embossment
Cathode (-)
Units Per Reel Case Code C D
Anode (+) Direction of Feed
Tape Width 12mm 12mm 12mm
Component Pitch 8mm 8mm 8mm
7" [178] Reel 500 500 400
13" [330] Reel 3000 2500 1500
E
www.vishay.com 46
For technical questions, contact tantalum@vishay.com
Document Number 40008 Revision 04-Feb-03

▲Up To Search▲

Price & Availability of 893D

	To Download 893D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .